Oasis PG8FEBF | Refrigerated Drinking Fountain w/ Contactless Bottle Filler
Shipping
Shipping
🚚✨ Free Shipping in the Continental U.S.
All Products. No Minimums.
Estimated Shipping Times:
Important Note on Delivery Times
All shipping estimates provided are approximate only. While we always strive to meet or exceed your delivery expectations, we cannot guarantee the exact delivery times listed.
For time-sensitive orders, please contact us directly so we can provide a more accurate lead time estimate based on your specific requirements.
Same Day Shipping
All in stock orders received before 3PM EST will ship the same day. Orders received after 3PM EST will ship the following business day.
Water Filters, Hand Dryers, & Indoor Bottle Fillers are our most popular in stock items.
Outdoor Tubular Drinking Fountains
Evergreen normally ships in 5-15 days. Black, Gray and Blue ship in 2-4 weeks.
Ice Machines
In stock units ship within 48 hours. Other units normally ship in 2-4 weeks.
Other
Orders that ship directly from a manufacturer normally have a firm shipping estimate but those dates are subject to change due to manufacturer production, inventory or shipping. We do our best to estimate ship dates but orders shipping directly from the manufacturer can have unexpected delays. We will confirm tracking information when orders ship directly from a manufacturer but may not have updates or estimates beyond the original estimate. Once your order is placed with the manufacturer, it may not be able to be cancelled even if it hasn't shipped yet.
Please contact support@bottlefillingstations.com to confirm delivery time for a specific product or quantity. Or to inquire about an existing order.
Special Case Shipping Rates
Please note that shipping rates are subject to change at any time. We reserve the right to charge an additional fee in addition to the regularly advertised shipping fee for shipping to remote areas not easily accessible by typical freight carrier means (i.e. islands only accessible by ferry). If your order falls into this category, you will be notified upon receipt of your order, and have the option to complete the purchase with additional fee or to cancel the order. Please note, these instances are very rare, as most locations are reachable by regular freight. If you have any questions, please contact us!
Key Terms & Conditions
Exceptions may apply to islands and other remote territories.
All orders shipped by the carrier of our choice.
Oasis PG8FEBF | Refrigerated Drinking Fountain w/ Contactless Bottl...
The Oasis PG8FEBF Series is a wall-mounted refrigerated drinking fountain with a contactless, filtered electronic bottle filler for indoor use.
Key Specifications:
| Finish | Greystone or Sandstone Powder Coat on Galvanized Steel; Stainless Steel |
| Activation | Contactless Sensor on Bottle Filler; Four Push Pads on Fountain |
| Filter Performance | VersaFilter III (FVF) reduces Lead, Particulate Class I, Chlorine Taste & Odor and Microplastics up to 4,750 Gal. Total PFAS (FPF) and Pharmaceutical (FRX) filter options also available |
| Refrigeration | 8.0 GPH of 50°F Drinking Water Included (R-134a Refrigerant) |
| Power | 115 Volts, 60 Hz, 5.0 Full Load Amps, 500 Rated Watts |
Why choose Oasis PG8FEBF Series:
- Chilled, Filtered Hydration: A high efficiency cooling system delivers 8.0 GPH of 50°F water, and the bottle filler offers filtration options for lead, chlorine taste and odor, microplastics, PFAS or pharmaceutical contaminants.
- Touch-Free Bottle Filling: The contactless sensor, laminar flow, programmable auto shut off, bottle counter and filter monitor make bottle filling easy to use and track.
- Built for Hygiene and Durability: A stainless steel top, heavy duty galvanized steel frame, lead-free waterways and Freshield silver-based antimicrobial protection on key components support long-term use.
- Easy Installation and Maintenance: Removable side and front panels, external stream height and thermostat adjustments, and a Tilt 'N Tether filter in the top bottle filler simplify setup and service.
Variant Option:
- PG8FEBFGST-FVF (507047FVF): Greystone powder coat finish with VersaFilter III filtration.
- PG8FEBFGST-FPF (507047FPF): Greystone powder coat finish with Total PFAS filtration.
- PG8FEBFGST-FRX (507047FRX): Greystone powder coat finish with Pharmaceutical filtration.
- PG8FEBFSAN-FVF (507048FVF): Sandstone powder coat finish with VersaFilter III filtration.
- PG8FEBFSAN-FPF (507048FPF): Sandstone powder coat finish with Total PFAS filtration.
- PG8FEBFSAN-FRX (507048FRX): Sandstone powder coat finish with Pharmaceutical filtration.
- PG8FEBFSTN-FVF (507049FVF): Stainless steel finish (additional cost) with VersaFilter III filtration.
- PG8FEBFSTN-FPF (507049FPF): Stainless steel finish (additional cost) with Total PFAS filtration.
- PG8FEBFSTN-FRX (507049FRX): Stainless steel finish (additional cost) with Pharmaceutical filtration.
FAQ
Q: What Are the Electrical Requirements for the Oasis PG8FEBF Series?
A: The unit runs on 115 Volts, 60 Hz, drawing 5.0 Full Load Amps and 500 Rated Watts. It requires a grounded North American duplex receptacle connected to a 20A minimum GFCI device.
Q: How Is the Filter Replaced on This Water Cooler?
A: The filter sits in the top bottle filler and is replaced with the Tilt 'N Tether system. A built-in filter monitor helps track filter life. The VersaFilter III replacement cartridge is OASIS Item #041145-001.
Q: What Plumbing Connections Are Needed for Installation?
A: The unit uses a 3/8" O.D. water inlet with strainer and a 1-1/4" O.D. tailpiece with 1-1/4" IPS waste. It operates between 20 and 100 PSI. The trap, stop valve and electrical outlet are not furnished.
NOTICE: Do not use with water that is unsafe or of unknown quality without adequate disinfection either before or after the system.
"Hydrate Everyone, Everywhere!" BottleFillingStations.com | Contact us
The Oasis PG8FEBF is a wall-mounted refrigerated drinking fountain with a contactless, filtered bottle filler, delivering 8.0 GPH of chilled water. Filter options include VersaFilter III, Total PFAS, and Pharmaceutical.
Before You Begin
- Tools: Power drill with pilot bit, T15 Torx driver, #2 Phillips and slotted screwdrivers, 1/4" nut driver, bubble level, and tape measure.
- Not included: Wall anchors and fasteners, a 1-1/4" P-trap, and a water shut-off valve.
- Plumbing: Provide a 3/8" water supply stub-out and a 1-1/4" IPS drain stub-out. Maximum supply pressure is 100 PSI. Use a regulator if pressure spikes could exceed it.
- Electrical and ventilation: The cooler and bottle filler each have a power cord, so you need two outlets or a splitter, on a 20A minimum GFCI device. Allow 4" of clearance per side for ventilation.
- Codes and reference: Some states require a licensed plumber. Check local codes for mounting height, and see the installation manual for the rough-in diagram.
Step-by-Step Installation Guide
- Hang the unit: Flush the building water supply line first. Mount the hanger bracket level with 2 anchors, then hang the unit on the galvanized steel frame, not under the stainless steel basin's return edge. Remove the front panel (2 T15 screws at the base and 2 under the fountain nose), mark the 2 lower anchor locations, then take the unit down to drill the pilot holes. Rehang and anchor it.
- Connect the drain: Install a P-trap between the drain stub-out and the basin drainpipe, cutting the drainpipe to fit if needed.
- Mount the bottle filler frame: Center the rubber gasket on top of the cooler against the wall. Set the wall frame on the gasket, mark the holes, and fasten it to the wall. Pull the plastic tubing up through the frame opening.
- Install and flush the filter: Insert the filter cartridge and turn it a quarter turn until it locks. Route the filter head's inlet tube through the frame and top to the water supply, and direct the outlet tube to the fountain drain. Turn on the water and flush the filter, then connect the outlet tube to the cooling tank inlet fitting.
- Connect and mount the bottle filler: Slide the sponge insulation over the water line and connect it to the solenoid valve inlet. Attach the tether to the cleat on the mounting frame. Feed the power supply terminals and green ground wire through the bushing in the cooler top, connect the terminals, and attach the ground wire to the cooler frame ground. Then set the cabinet into the gasket groove and secure it with the supplied Torx screws.
- Power up and test: Spin the condenser fan blade by hand to confirm it's clear, then plug in both power cords. Turn on the water and place a container in the alcove to release trapped air, then check for leaks. Adjust the fountain stream to at least 4" high. Reinstall the front panel and the bottle filler top cap.
Looking for the Oasis PG8FEBF Refrigerated Fountain with Filtered Bottle Filler?
