Oasis MW8EBF | In-Wall Refrigerated Bottle Filler w/ Contactless Sensor
Shipping
Shipping
🚚✨ Free Shipping in the Continental U.S.
All Products. No Minimums.
Estimated Shipping Times:
Important Note on Delivery Times
All shipping estimates provided are approximate only. While we always strive to meet or exceed your delivery expectations, we cannot guarantee the exact delivery times listed.
For time-sensitive orders, please contact us directly so we can provide a more accurate lead time estimate based on your specific requirements.
Same Day Shipping
All in stock orders received before 3PM EST will ship the same day. Orders received after 3PM EST will ship the following business day.
Water Filters, Hand Dryers, & Indoor Bottle Fillers are our most popular in stock items.
Outdoor Tubular Drinking Fountains
Evergreen normally ships in 5-15 days. Black, Gray and Blue ship in 2-4 weeks.
Ice Machines
In stock units ship within 48 hours. Other units normally ship in 2-4 weeks.
Other
Orders that ship directly from a manufacturer normally have a firm shipping estimate but those dates are subject to change due to manufacturer production, inventory or shipping. We do our best to estimate ship dates but orders shipping directly from the manufacturer can have unexpected delays. We will confirm tracking information when orders ship directly from a manufacturer but may not have updates or estimates beyond the original estimate. Once your order is placed with the manufacturer, it may not be able to be cancelled even if it hasn't shipped yet.
Please contact support@bottlefillingstations.com to confirm delivery time for a specific product or quantity. Or to inquire about an existing order.
Special Case Shipping Rates
Please note that shipping rates are subject to change at any time. We reserve the right to charge an additional fee in addition to the regularly advertised shipping fee for shipping to remote areas not easily accessible by typical freight carrier means (i.e. islands only accessible by ferry). If your order falls into this category, you will be notified upon receipt of your order, and have the option to complete the purchase with additional fee or to cancel the order. Please note, these instances are very rare, as most locations are reachable by regular freight. If you have any questions, please contact us!
Key Terms & Conditions
Exceptions may apply to islands and other remote territories.
All orders shipped by the carrier of our choice.
Oasis MW8EBF | In-Wall Refrigerated Bottle Filler w/ Contactless Se...
The Oasis MW8EBF (506975) is an in-wall refrigerated contactless bottle filler delivering 8.0 GPH of chilled water.
Key Specifications:
| Finish | Brushed Stainless Steel Cabinet and Alcove |
| Activation | Contactless Sensor with Programmable Auto Shut Off |
| Filtration | Non-Filtered. Optional OASIS VersaFilter III Kit (041253-001), Total PFAS Kit (041253-005) or Pharmaceutical Kit (041253-006) Can be Added for Filtered Option |
| Refrigeration | 8.0 GPH of 50°F Water Chiller Included (R-134a Refrigerant) |
| Power | 115 Volts, 60 Hz, 5.0 Full Load Amps, 500 Rated Watts |
Why choose Oasis MW8EBF:
- Chilled Water On Demand: The high efficiency cooling system delivers 8.0 GPH of 50°F drinking water at 90°F ambient and 80°F inlet water.
- Touch-Free Bottle Filling: Contactless sensor activation with laminar flow and programmable auto shut off supports a more hygienic, splash-controlled fill.
- Space-Saving In-Wall Design: The recessed design includes a heavy duty galvanized steel frame, a stainless steel alcove and cabinet, and an LED lighted alcove.
- Cleaner, Easier Maintenance: A built-in 100 micron strainer, lead-free waterways, Freshield antimicrobial protection, a filter monitor with bottle counter, and locking access panels simplify upkeep.
FAQ
Q: What Is Needed for Installation of the Oasis MW8EBF?
A: The recessed mounting frame is included, but a water supply and plumbed drain are required. The drain needs a 1-1/2" or 1-1/4" IPS waste stub out and a short radius trap. The stop valve, trap and pipe connector to the waste line are not provided.
Q: What Electrical Connection Does the Oasis MW8EBF Require?
A: It runs on 115 Volts, 60 Hz and draws 5.0 full load amps (500 rated watts). It needs a 115V grounded North American duplex receptacle connected to a minimum 20A GFCI device to meet UL requirements.
Q: Can Filtration Be Added to the Oasis MW8EBF?
A: Yes. The unit is not filtered as standard, but filtration can be added at additional cost. Options are the OASIS VersaFilter III (041253-001), Total PFAS (041253-005) and Pharmaceutical (041253-006) Universal Retrofit Kits.
NOTICE: Do not use with water that is unsafe or of unknown quality without adequate disinfection either before or after the system.
"Hydrate Everyone, Everywhere!" BottleFillingStations.com | Contact us
The Oasis MW8EBF is an in-wall refrigerated bottle filler with a contactless sensor, delivering 8.0 GPH of chilled water.
Before You Begin
- Plumbing: Provide a 3/8" O.D. water supply and a 1-1/2" or 1-1/4" IPS waste stub-out. Maximum supply pressure is 100 PSI. The stop valve, short radius P-trap, and waste pipe connector are not included.
- Electrical: A 115V grounded duplex receptacle on a 20A minimum GFCI device is required. A 2x4 junction box is provided, and flexible conduit is recommended.
- Wall opening: Prepare the opening and rough-in per the manual's roughing-in drawing, and allow extra depth for the water and waste lines.
- Codes and reference: Some states require a licensed plumber. See the user guide for rough-in dimensions and electronics setup.
Step-by-Step Installation Guide
- Install the frame: Insert the frame into the wall opening and secure it to the studs. The front flange must sit flush with the finished wall. Set the drip tray in the frame without fastening it, and install the snap bushings.
- Mount the chiller: Attach the cradle mounting angles to the frame flange without tightening, slide the cradle between them, then fasten it with the supplied screws and tighten all. Place the chiller in the cradle.
- Connect the water: Run the supplied ball valve and 3/8" copper tube to the building supply. Fit 1/4" unions on the chiller inlet and outlet. Connect the solenoid valve outlet to the chiller inlet, and the chiller outlet to the bottle filler delivery fitting.
- Connect the drain: Install a short radius P-trap between the frame's waste tailpiece and the waste stub-out.
- Wire and mount the upper panel: Route the push button wire and tubing through the frame opening. As you set the panel in place, feed the long green ground wire and power cord terminals through the bushings. Attach the green wire to the junction box ground, plug in the cord, and fasten the panel with the supplied screws. The unit won't work without the ground wire.
- Test and finish: Turn on the water and check all connections for leaks. Fasten the lower panel with the supplied locks or screws, then secure the drip tray grille with its 3 flathead screws.
Looking for the Oasis MW8EBF In-Wall Refrigerated Bottle Filler?
